Vg310 ios download

You are commenting using your Twitter account. You are commenting using your Facebook account. Notify me of new comments via email. Notify me of new posts via email. Skip to content. Save and Reboot, then continue. Step 3 To continue with the configuration, enter yes. The following message is displayed: Would you like to enter basic management setup? Step 4 Enter yes to continue. The following message is displayed: Configuring global parameters: Enter host name [Router]: Step 5 Enter a hostname for the voice gateway.

The following message is displayed: The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: Step 6 Enter an enable secret password. The following message is displayed: The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images.

Enter enable password: Step 7 Enter an enable password that is different from the enable secret password. The following message is displayed: The virtual terminal password is used to protect access to the router over a network interface.

Enter virtual terminal password: Step 8 Enter the virtual terminal password and press Enter. A summary of the available interfaces is displayed, as shown in the following example: Current interface summary Interface IP-Address OK?

Enter 2 to save the initial configuration: [0] Go to the IOS command prompt without saving this config. Enter your selection [2]: 2 Building configuration Use the enabled mode 'configure' command to modify this configuration. Step 13 To save the configuration, enter yes. The following message is displayed: Use this configuration? Procedure Step 1 Enter no as the response when the following system message is displayed: Example: System Configuration Dialog At any point you may enter a question mark '?

Copyright c by cisco Systems, Inc. Table 1. Power on the chassis. Faulty power cable. Faulty power source. Faulty internal power supply. Contact Cisco or your Cisco reseller. Faulty cabling to terminal. Check and replace the cable, if required.

Unit shuts off after operating for some time Overheating. Check the ventilation of the chassis. Console screen display freezes Console fault. Reset or replace the console. Software error. Updated: February 8, To redisplay a command you previously entered, press the Up Arrow key. You can continue to press the Up Arrow key for more commands. Router config-if To exit to global configuration mode, use the exit command. Undoing a Command or Feature If you want to undo a command you entered or disable a feature, enter the keyword no before most commands; for example, no ip routing.

Saving Configuration Changes You need to enter the copy running-config startup-config command to save your configuration changes to nonvolatile random-access memory NVRAM , so the changes are not lost if there is a system reload or power outage. For example: Router copy running-config startup-config Building configuration Remember that: You can use the question mark? Each command mode restricts you to a set of commands. If you have difficulty entering a command, check the prompt and then enter the question mark?

To disable a feature, generally enter the keyword no before the command; for example, no ip routing. You need to save your configuration changes to NVRAM so the changes are not lost if there is a system reload or power outage. If you do not hold a valid Cisco service contract, please contact your reseller.

The Cisco TAC website is available 24 hours a day, days a year. P3 and P4 cases are those in which your network is minimally impaired or for which you require product information. After you describe your situation, the TAC Case Open Tool automatically recommends resources for an immediate solution. If your issue is not resolved using the recommended resources, your case will be assigned to a Cisco TAC engineer.

For P1 or P2 cases, cases in which your production network is down or severely degraded or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly. To open a case by telephone, use one of the following numbers:. To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.

You and Cisco will commit all necessary resources around the clock to resolve the situation. Priority 2 P2 —Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Priority 3 P3 —Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels. Priority 4 P4 —You require information or assistance with Cisco product capabilities, installation, or configuration.